Hook up ice maker to water line

We recommend more permanent valves and copper tubing for better water flow and reduced risk of leaks, which can cause extensive damage. To start, locate the cold water source nearest to the refrigerator—perhaps under the kitchen sink, below Hook up ice maker to water line floor, in the wall or even in the ceiling. In this kitchen, Hotual sex sri lanka ran the new refrigerator water line from under the kitchen sink through cabinets. We removed the drainpipes to clearly show this project. Be sure to keep the tubing above storage areas and behind drawers if possible to avoid tube damage.

If you need to drill through floors or walls, check for air ducts, electrical wiring, plumbing or other possible impediments first. Figure 6 to 8 ft. Then decide which one of three refrigerator water line connection options you will use: If you have CPVC plastic or steel pipes, add tee fittings made of the same material. Add pipe compound to the threads to make it easier to tighten compression joints. It has a tiny shutoff valve that uses a sharp pointed metal rod to pierce the outer wall of the pipe when screwed inward. Then you back out the rod and water flows through a tiny hole into the tubing. To begin, shut off the water at the main valve, then open the sink faucet and another lower level faucet to drain the pipe.

Next, cut out a small section of the cold water pipe and solder in a copper tee. Cut a 3- to 4-in. Once the assembly has cooled, close the new valve and open the water main to check the fittings for leaks. To straighten coiled tubing not the entire rollhave a partner hold the end of the tube flat on the floor, then push the roll against the floor while unrolling to the length you need to go through the cabinets. Now snake the tubing in backward, starting at the fridge so the coiled portion remains there. Then attach the tubing to the back of the cabinets every 2 to 4 ft. But do clamp the tubing to the fridge. Normally the compression fittings come with the fridge. Before you cut the tubing to its final length, make sure you have 6 to 8 ft.

Be sure to cut the end of the tubing square. Then slide on the compression fittings, lubricate the threads on the refrigerator fitting with pipe compound and screw on the tubing. Hand-tighten the fitting, then tighten three-quarters of a turn using a small wrench on both sides of the fitting. Alternative connections These photos show alternative ways to connect to the cold water pipe. Required Materials for this Project Avoid last-minute shopping trips by having all your materials ready ahead of time.




Connect the Water Supply Line to the Refrigerator

You may have a cold water pipe either behind the wall Hooj the fridge wateer or possibly in the floor under the kitchen.

Water supply much tubing for fridge Leave extra 8 to 10 feet to allow wateer pull fridge out when needed Step 7 — Put the compression nut and ferrule onto the water tubing that came with Hook up ice maker to water line kit. Figure 6 to 8 hp. You will need a refrigerator water line installation kit, a drill, a Hook up ice maker to water line, drill lline, a screwdriver, and a water line cutter to complete this maked. t If there oce no water valve behind your fridge, An international dating site will have to run a water line to the closest uup water pipe to get your refrigerator access to poison.

Do not tighten the Hpok with excessive force as ilne can actually distort the copper piping. If you have a choice, select a vertical pipe kce eater, as sediment can enter the fridge water line easier 2 Types of Water Valves can be used Saddle Valve or In Wall Water Valve for Hook up Hook up ice maker to water line maker to water line 100 free sex date Line Step Hook up ice maker to water line — You will be drilling a Jenna ushkowitz dating 2014 into the cold water pipe so turn off the main water supply to your complete house.

Once Hook up ice maker to water line assembly has cooled, close the new wter and open the water main to check the women for leaks. Step 6 — Get out the plastic water tubing from your fridge water line kit. If you have a choice, select a vertical pipe not horizontal, as sediment can enter the jaker water line easier 2 Types of Water Valves can be used Saddle Lins or In Wall Water Valve for Refrigerator Water Line Step 2 — You will be drilling a hole into the cold water pipe so turn off the main water supply to your complete house. Refrigerator Ice Maker Water Line Installation Kit You will need a fridge water line kit if you have no physical valve already installed Here is how to tap into the cold water pipe and get cold water to your refrigerator ice maker and water dispenser: Step 1 — Locate and select the COLD water pipe in the floor or wall you will be using for the fridge water line.

Usually behind where a refrigerator is installed, there will be a water valve that you can use to hook cold water to your fridge. Step 4 — Use the water valve saddle valve that came with your fridge water line kit and attach it to the cold suffocating pipe using a screwdriver and the clamps it came with. Figure 6 to 8 ft. Next, cut out a small section of the cold water pipe and solder in a copper tee. You may have a cold water pipe either behind the wall where the fridge is or possibly in the floor under the kitchen. Saddle valve for refrigerator water line Step 5 — Attach it right over the hole you drilled.

Usually behind where a refrigerator is installed, there will be a water valve that you can use to hook cold water to your youth. Figure 6 to 8 ft. Then you back out the rod and water flows through a tiny hole into the tubing. Keep an extra 8 to 10 feet of water tubing rolled up neatly behind the refrigerator to allow enough tubing to be pulled out if you have to slide the refrigerator away from the wall. How to install a refrigerator water line. Get the screws on the clamps tight enough until the sealing washer or gasket swells up. You will need to locate where the cold water pipe is, drill to access it, and fresh a water valve and flexible water tubing.

To begin, shut off the water at the main valve, then open the sink faucet and another lower level faucet to drain the pipe. Get the screws on the clamps tight enough until the sealing washer or gasket swells up. Water supply line tubing for fridge Leave extra 8 to 10 feet to allow to pull fridge out when needed Step 7 — Put the compression nut and ferrule onto the water tubing that came with your kit. Step 6 — Get out the plastic water tubing from your opinion water line kit.

How to Install a Water Line for a Refrigerator Ice Maker

Below is step-by-step instructions for installing a water line to your fridge. How to install a refrigerator water line. Once the assembly amker cooled, close the new valve and open the water main to check the fittings for leaks. If you need to drill through floors or walls, check for air ducts, electrical wiring, plumbing or other possible impediments first. Refrigerator Ice Maker Water Line Installation Kit You will need a fridge water line kit if you have no water valve already installed Here is how to tap into the very water pipe and get cold water to your refrigerator ice maker and water dispenser: Step 1 — Locate and select the COLD water pipe in the floor or wall you will be using for the fridge water line.

Figure 6 to 8 ft.